Peterson Portable Sawmills

Swingmill Blade Maintenance – Portable Sawmills

Kerris Browne

Part 1 of a 5 part series covering all you need to know about swingmill blades – by Kerris Browne

This issue’s focus: Blade Maintenance & Identification

Have you heard some good things about swingmills, but don’t know enough about the blade technology? Circular swingmill blades are completely different to bandsaw blades, and this 5-part series focuses purely on demystifying the ‘swingmill’ blade.

First up, what is a swingmill?

A swingmill has a single circular blade that pivots; it moves forward sawing in horizontal to make the first cut, pivots to vertical at the end of the log, and then moves back to its starting position as it saws in vertical. Your dimensional board can now be removed from the log completely edged and square. The log remains completely still and there’s no edging or resawing involved.

Peterson Portable Sawmills in New Zealand were the first designers and manufacturers in 1989, followed by Ecosaw
and then Lucas in Australia in 1995. Swingmills are the sawmill of choice in these countries, as well as in many of the
surrounding Pacific Islands and Africa. But swingmills are still in the ‘gaining popularity’ phase in many northern hemisphere countries such as the US, Canada, and Europe, simply because there is not enough information out there
yet.

OK, lets look at some blades!

Brand new swingmill blade out of the box

Brand new blade

Here’s a brand new blade straight out of the box; all sleek and shiny. It won’t look like this for very long though. As you handle it, salt and sweat from your hands can start minor rust. Even in dry storage, your hand prints will be visible in a few days. But that’s no problem unless you’re trying to sell a brand new blade that already looks secondhand…

You may now be asking what the holes are for, right? These are actually called Strobe Slots, where small planer knives or ‘Strobe Knives’ can be mounted. When you are cutting very fibrous timber like Cottonwood, the furry timber rubs the side of the blade causing friction and heat. It’s usually very slow to cut, so many sawmillers don’t even bother with logs of this species. But if you install Strobe Knives in the slots, they effectively clear away the rough surfaces in the sawing path, and allow the blade to continue sawing unhindered. Strobe Knives can make all the difference between a 2-hour job and a 2-day job! Plus the slots allow water to travel through and lubricate both sides of the blade, reducing uneven heating.

Swingmill Sawmill blade in good working order.

Working blade

Next is a perfectly good, working blade from the field. This particular one is 5 years old, and I can tell you this operator works his blades really hard! But this blade is in very good condition, and the marks and colors are completely normal. The brownish areas behind the teeth and gullets are just sap and sawdust rub marks. The owner has also left this blade out in the rain a few times – you can spot some rust pitting in the dark dotted areas. Minor pitting like this is not a big deal. Nevertheless, a blade should not be left wet for weeks at a time, as the pits can get quite deep and then weaken the structure of the blade.

Sawmill blade with minor surface rust from storage

Minor surface rust from storage

Now here’s a blade you’d think is destined for the scrap heap – but not so! Blade steel is chosen for its strength – not its rust resistance. This blade is still fine. It’s just covered in surface rust from moisture in the air during long-term
storage [yep, under cover]. There aren’t any pit marks or indentations that would come from wetness; it’s only a very light, but ugly, surface dusting of rust. All you need to do is give the area around the mounting holes a light sand with
very fine sandpaper, to ensure it can mount flush and tight to the hub. The rest of the rust will come off with your first few boards. The number of teeth on a swingblade, changes the performance. For example, fewer teeth with a thinner tooth are better for hardwoods, yet more teeth and wider teeth perform better in soft or fibrous timbers. More teeth give a better finish, but can be slower cutting as each tooth is only taking out a small bite. It’s important that a manufacturer gets the balance right between horsepower, plate thickness, number of teeth and tooth width, to give optimum performance.

Buy genuine brand; it’s safer and more effective

If you are considering getting a replacement blade made locally instead of purchasing from the manufacturer, you may need to think again. Each brand of swingmill has carefully designed their blades specifically for their mill, unlike bandsaws which are often generic. A swingmill blade’s artistic design, shape, and patterns are automatically copyrighted to the original designers. And this is an international law, so it doesn’t really matter that the mill is made somewhere else and imported. Inferior quality blade copies can also make sawing a real nightmare; if the plate is too thin it will vibrate about, be hard to push, and cut rough.

Maximum RPM stamped on the sawmill blade

Maximum RPM

Safety also has to be considered when it comes to details like ensuring the blade screws are completely level with the surface of the blade. Export manufacturers of swingmills will have spent a lot of time at the R&D stage, getting their machines up to CE Safety standards for the European market. This is one of the most stringent safety standards in the world, and close attention is paid to the blades. A blade that has CE should have a maximum rpm stamped on the body, to ensure it is not operated beyond a safe working speed. And if you ever have a problem with your blade, you can always get support from the genuine manufacturer. So considering a good blade can last you 6-8 years or more, it’s a smart decision to just get a new blade from the designers themselves.

When purchasing a secondhand mill, also inspect the blades closely for stress fractures and cupping (loss of tension), and then give them a test run if they look OK. It’s recommended you have a sawdoctor to check whether the body steel is beyond it’s shelf life. How to check teeth, gullets, and blade steel care will be covered in more detail in later issues.

There are 4 more sections of this article yet to come, which will be published in forthcoming issues;
· Re-Tipping & Sharpening
· Plate (Body), Gullets & Tensioning
· Blade Adjustments to Run True
· Maintenance & Running Costs

« Return to 'Portable Sawmill News and Articles' index

6 comments shared

  1. Eckart Lampe says:

    please send information and price
    for

    swingmills blades

    TBFA GmbH Engineerings Service
    Birbacherstr.15
    D-84364 Bad Birnbach Germany

  2. Larry Sweet says:

    Please send price for your 10 inch swing blade

  3. Frank Mitiel says:

    Hello there,

    Can you kindly send me the cost of the Blades please?

    regards
    Frank

Share your comments